100% success and guarantee to pass Cisco 200-125 exam test easily at first try with latest Cisco CCNA 200-125 dumps exam questions and answers. https://www.lead4pass.com/200-125.html dumps pdf practice files. High quality Cisco CCNA 200-125 dumps pdf training materials and study guides, the best Cisco CCNA 200-125 dumps pdf and vce practice materials free download at Lead4pass.
Download free latest Cisco 200-125 dumps pdf from google drive: https://drive.google.com/open?id=0B_7qiYkH83VRSnZDMkVUWDJzLWM
Download free latest Cisco 300-320 dumps pdf from google drive: https://drive.google.com/open?id=0B_7qiYkH83VRU3Y3elpyNldxUU0
What is the function of the command switchport trunk native vlan 999 on a Cisco Catalyst switch?
A. It creates a VLAN 999 interface.
B. It designates VLAN 999 for untagged traffic.
C. It blocks VLAN 999 traffic from passing on the trunk.
D. It designates VLAN 999 as the default for all unknown tagged traffic.
Which two of these are characteristics of the 802.1Q protocol? 200-125 pdf (Choose two.)
A. It is used exclusively for tagging VLAN frames and does not address network reconvergence following switched network topology changes.
B. It modifies the 802.3 frame header, and thus requires that the FCS be recomputed.
C. It is a Layer 2 messaging protocol which maintains VLAN configurations across networks.
D. It includes an 8-bit field which specifies the priority of a frame.
E. It is a trunking protocol capable of carrying untagged frames.
QUESTION 3 200-125 dumps
Which three of these statements regarding 802.1Q trunking are correct? (Choose three.)
A. 802.1Q native VLAN frames are untagged by default.
B. 802.1Q trunking ports can also be secure ports.
C. 802.1Q trunks can use 10 Mb/s Ethernet interfaces.
D. 802.1Q trunks require full-duplex, point-to-point connectivity.
E. 802.1Q trunks should have native VLANs that are the same at both ends.
Assuming the default switch configuration, which VLAN range can be added, modified, and removed on a Cisco switch?
A. 1 through 1001
B. 2 through 1001
C. 1 through 1002
D. 2 through 1005
Refer to the exhibit. The output that is shown is generated at a switch. Which three statements are true? (Choose three.)
A. All ports will be in a state of discarding, learning, or forwarding.
B. Thirty VLANs have been configured on this switch.
C. The bridge priority is lower than the default value for spanning tree.
D. All interfaces that are shown are on shared media.
E. All designated ports are in a forwarding state.
F. This switch must be the root bridge for all VLANs on this switch.
A network administrator is verifying the configuration of a newly installed host by establishing an FTP connection to a remote server. 200-125 pdf What is the highest layer of the protocol stack that the network administrator is using for this operation?
F. data link
Refer to the exhibit. Each of these four switches has been configured with a hostname, as well as being configured to run RSTP. No other configuration changes have been made. Which three of these show the correct RSTP port roles for the indicated switches and interfaces? (Choose three.)
A. SwitchA, Fa0/2, designated
B. SwitchA, Fa0/1, root
C. SwitchB, Gi0/2, root
D. SwitchB, Gi0/1, designated
E. SwitchC, Fa0/2, root
F. SwitchD, Gi0/2, root
What is one benefit of PVST+?
A. PVST+ supports Layer 3 load balancing without loops.
B. PVST+ reduces the CPU cycles for all the switches in the network.
C. PVST+ allows the root switch location to be optimized per VLAN.
D. PVST+ automatically selects the root bridge location, to provide optimized bandwidth usage.
Refer to the exhibit. The network administrator normally establishes a Telnet session with the switch from host A . However, host A is unavailable. The administrator’s attempt to telnet to the switch from host B fails, but pings to the other two hosts are successful. What is the issue?
A. Host B and the switch need to be in the same subnet.
B. The switch interface connected to the router is down.
C. Host B needs to be assigned an IP address in VLAN 1.
D. The switch needs an appropriate default gateway assigned.
E. The switch interfaces need the appropriate IP addresses assigned.
Refer to the exhibit. Which two statements are true about interVLAN routing in the topology that is shown in the exhibit? (Choose two.) 200-125 dumps
A. Host E and host F use the same IP gateway address.
B. Router1 and Switch2 should be connected via a crossover cable.
C. Router1 will not play a role in communications between host A and host D
D. The FastEthernet 0/0 interface on Router1 must be configured with subinterfaces.
E. Router1 needs more LAN interfaces to accommodate the VLANs that are shown in the exhibit.
F. The FastEthernet 0/0 interface on Router1 and the FastEthernet 0/1 interface on Switch2 trunk ports must be configured using the same encapsulation type.
Read more: https://www.lead4pass.com/200-125.html dumps pdf training materials and study guides free download.
Watch the video to learn more: